MPro7 Gun Cleaner

Originally developed to clean the $28 million dollar F-16 for the US Air Force, MPro7 Gun Cleaner's special blend of chelating agents, corrosion inhibitors and surfactants in a non-toxic solvent base are actually able to safely penetrate into the pores of metal. MPro7 is the most safe and effective way to clean carbon, oil and grease available in the world.  This technology has never before been available to the public, until now. The cleaning result is a bare metal surface that is completely devoid of all contaminants. The firearm will be cleaner than when shipped from the factory.  In addition, MPro7 Gun Cleaner is safe to use on all rifles, handguns, shotguns, machine guns, grenade launchers, artillery pieces, cannons, black powder firearms, corrosive priming deposits, stainless, blued & nickel finishes, titanium, Polycarbonate plastics (e.g. Smith & Wesson's SIGMA^®,  Glock^®, Heckler & Koch^® frames), rubber, nylon, varnished and urethane woods.

Bore Conditioning The first cleaning with MPro7 Gun Cleaner may take a bit longer than normal since MPro7 removes carbon that has been in the bore since the first test fire (cleaning new firearms enhances the bore conditioning). Continuous firing bonds carbon, lead and most copper fouling to the bore metal in layers.  No other cleaner can remove these stubborn layers of carbon and metal fouling.  Therefore, it takes MPro7 some time and multiple applications to penetrate these old layers and remove them permanently. The key is dwell time and agitation. The longer MPro7 sits, the less agitation is required. Typically, 5 to 10 minutes is enough.  Once these layers are removed, subsequent cleaning time and effort can be reduced by up to 80% (depending on the degree of build up). With a surface completely devoid of carbon deposits, it takes longer for fouling to build up and it does not adhere as easily to the bore.

Stainless Steel & Nickel Anyone who has a stainless steel or nickel revolver gets frustrated cleaning the cylinder face, forcing cone and top strap because there are no cleaners that will remove the black carbon staining. Now, you can tell friends and family that you know how to remove it in 30 seconds!  Just spray MPro7 on the carbon, let it sit for 5 minutes and then scrub with a stainless steel brush (tooth type) lightly for about 30 seconds.  The degree of effort to clean is less than you would expend brushing your teeth and the results are visible immediately!  Your friends will thank you for solving this age old and frustrating problem.

Black Powder MPro7 neutralizes the corrosive effects of black powder residue. MPro7 Gun Cleaner breaks up the fouling and conditions the bore on a microscopic level.  Some black powder shooters are concerned about  MPro7's effect on their barrel seasoning and firearm accuracy. After cleaning with MPro7, you are left with a totally clean bore surface.  A microscopic layer of rust inhibitor and dry lube remains. This layer is an extremely efficient bore conditioner.  When combined with oil, it helps to protect your firearm from rust and corrosion. This bore conditioning replaces traditional barrel seasoning. This not only improves accuracy, but also cuts future  cleaning time in half, because powder, lead and plastic residue cannot penetrate into the steel as before.

Shotguns MPro7 Gun Cleaner safely and quickly removes lead and plastic shot cup fouling…even in shotguns with interchangeable choke tubes.  Although MPro7 does not affect plastics, the plastic fouling becomes "carbonized".  MPro7 pulls the carbon out of the plastic causing the plastic fouling to curl up. A little brushing will remove it easily.

Rust Prevention MPro7 completely strips a firearm of any oil or grease so it is important to oil the firearm completely after cleaning (see MPro7 Ultimate Gun Lubrication). Also, MPro7 will remove light rust. Just spray it on, let sit for 2 minutes and lightly brush with a nylon or bronze bristle brush. MPro7 will not remove standard factory bluing.

Ultrasonic or Dip Applications MPro7 Gun Cleaner is perfect to use in Ultrasonic, Dip Tanks or even Tupperware^® type plastic containers.  Breakdown the firearm and remove the grips, stocks and/or optics. Let the parts soak in the solution for approximately 15 minutes. Then, follow the MPro7 Process as necessary. Dry completely and re-oil thoroughly.  We recommend a full immersion in our MPro7 Ultimate Gun Lubrication.  It will penetrate and protect the internal mechanisms, yet when wiped off the exterior of the firearm, will not leave a greasy or slippery surface.  MPro7 Gun Cleaner can be reused many times. To increase the cleaning life, filter the solution through a cloth.
4oz pump spray  $7.99
8oz pump spray  $12.99
32oz trigger spray  $27.99

MPro7 Bore Cleaning Gel

This product has all of the properties of MPro7 Gun Cleaner, just in an easy to use gel form.  It was designed for people who asserted that it was difficult to spray cleaner into small bore rifles and handguns.  We listened.  MPro7 Bore Gel is not as thick as most gels because less is needed to clean. If you want to thicken it, simply place the jar in the refrigerator for approximately 15 minutes.
4oz Gel  $8.99
8oz Gel  $14.99